Showing 10 results for Arab
Farshid Ali Arabian, Majid Motamedzade, Rostam Golmohammadi, Abbas Moghim Beigi, Fereshteh Pir Hayati,
Volume 1, Issue 1 (Journal of Ergonomics 2013)
Abstract
Introduction: One of the major problems in hospitals
leading to high prevalence of musculoskeletal disorders among the health staff
is associated with patients handling. This study was aimed to reduce
musculoskeletal disorders using ergonomic intervention among Nahavand
Alimoradian hospital staff.
Material and Methods: This study was conducted in four wards of
160-bed Nahavand Alimoradian hospital. The data collecting tool was Nordic
Musculoskeletal Questionnaire. SPSS software was used for data analysis. The
questionnaire was completed, before and after educational intervention, for 46
employees of the four wards which had the most complaints about musculoskeletal
disorders. Training classes were held
for the target group covering prevention of work-related musculoskeletal
disorders, proper techniques for patient handling and stretching exercises for
low back pain prevention.
Results: The main results tended to be the high
prevalence of musculoskeletal disorders especially in low back, shoulders and
wrists of the employees. Low back pain was the most prevalent disorder among
the personnel. The educational intervention had not significant effect on
lessening the musculoskeletal disorders in hospital staff (p > 0.05).
Conclusion: At
present, regarding enhancements in healthcare procedures, there is an urgent
need to ergonomic intervention in the design of environment, tools and
equipment concurrent with educational intervention.
Normal
0
false
false
false
EN-US
X-NONE
FA
Mohsen Taghizade, Iraj Mohebbi, Hamidreza Khalkhali, Parya Ahmadi-Arablu, Arezou Torfeh, Mohammad Hajaghazadeh,
Volume 6, Issue 1 (Journal of Ergonomics 2018)
Abstract
Background: The lack of fit between tools and human hand could result in musculoskeletal disorders and decrease efficiency. Designing hand tools, anthropometric data of target population is necessary. A few studies have reported the hand anthropometric dimensions of Iranians. Therefore, the aim of the present study was to measure the most important anthropometric dimensions of hand in a population of office staffs in Urmia.
Methods:In this study, 20 dimensions of dominant hand were measured in 345 participants (217 males and 128 females) using a digital caliper and a plastic tape. The important percentiles were reported by gender. Independent t-test was used to compare the mean of male and female hand dimensions. The length and width of hand were compared with the corresponding data from published literature.
Results: The values of 5th, 50th, and 95th percentiles were calculated and tabulated by gender. The hand dimensions of men were larger than those of women. The mean of hand dimensions of men was statistically different from those of women (P=0.001). In contrast to women, the hand length and breadth of the men of this study were significantly different from those of the most of the other communities.
Conclusion: The results of this study could be used by designers or importers of hand tools and gloves. Considering the significant differences of hand dimensions between men and women, it is recommended to use hand dimensions of each gender for designing their related products.
Majid Lashgari, Mohammadreza Arab,
Volume 6, Issue 3 ( Iranian Journal of Ergonomics 2018)
Abstract
Background & Objectives: Sound as a detrimental factor in working environments can create annoying conditions for people in addition to physical problems. Therefore, in addition to evaluating quantitative parameters such as pressure levels, it is absolutely necessary to study the quality parameters of the sound in the work environment.
Methods: In this descriptive-analytic research, the sound of 285 MF tractor was recorded. Then, the EEG of five drivers were recorded in the pre-driving state and then when driving with the tractor in four different engine speed. The psychoacoustic annoyance model was used to assess the annoyance of tractor drivers. Then means were compared with Duncan comparison test at 5% probability level and the correlation between psychoacoustic acoustic and alpha and beta bands was determined.
Results: The results of ANOVA showed that different levels of engine speed on psychoacoustic annoyance were significant at 1% probability level. The results also showed a decrease in the amplitude of the alpha band, as well as an increase in the beta band amplitude due to increased engine speed. Regression results showed that there is a high correlation between the two alpha and beta bands and the psychoacoustic annoyance, so that the detection coefficient was 0.966 and 0.998, respectively, for the two bands alpha and beta.
Conclusion: This study showed that changes in the quality parameters of the sound and consequently the resulting annoyance caused the amplitude changes in both the alpha and beta bands. So, it can be concluded that the psychoacoustic annoyance is a good indicator of brain activity.
Dr Ehsanollah Habibi, Emad Mirsalimi, Faezeh Darabi, Kamran Ebrahimi,
Volume 6, Issue 4 ( Iranian Journal of Ergonomics 2019)
Abstract
Background and Objectives: This study focused on lifting drill rods. Drilling is a repetitive and heavy mining operation with a high incidence and severity of musculoskeletal injuries. The purpose of this study was to examine how to lift a vertical drill bit (1.61m and 35kg in height) using two types of rod height and four feet positions, and finally compare them with the Lifting Index (LI).
Methods: Seven workers participated in this study. Each person raised a rod and held it vertically. Reflective markers were installed on each person, and from three cameras and an Ergo-meter plate for record forces and Movement of the limbs. In this case, four positions of the foot and pressures on the lower back were Investigated (position0=to the rod, position45=diagonally to the rod, position90=right side of the bar and free posture). In addition, two positions of the height of the rod were Investigated, at the first, the end of rod was on the ground (height of the rod was 83 m), and in the following the end of rod was on the Basket with height 20cm (rod height of 1.03 m).
Results: The Lifting Index (LI) for each person was equal to 1.4 in the NIOSH lifting equation. It was found that the vertical height of the rod had the greatest effect at the load on the lower back. Some workers use techniques that endure less pressure on their waist.
Conclusion: Finally, it was found that the asymmetric loading Condition (90 ° angle) was the worst case compared to the Lifting index and NIOSH standard.
Ali Arabian, Seyed Abolfazl Zakerian,
Volume 7, Issue 1 (Iranian Journal of Ergonomics 2019)
Abstract
Background and Objectives: The use of new technologies, particularly mobile phones, is drastically growing on a daily basis. The usability of mobile phones can be determined for different age groups in order to reach a balanced development plan with respect to this technology. The present study aimed to investigate and compare the usability of touch-screen and button cell phones among Iranian elderly users, with respect to objective performance and perceived usability.
Methods: In this cross-sectional study, 20 elders (50% female) with an average age of were selected by simple random sampling method to measure the usability of touch-screen and button cell phones. In order to assess the objective performance of how elders work with cell phones, tests were conducted including items like typing speed, number of typing errors, taking photo, creating new contacts, and sending text messages. Perceived usability was obtained using a questionnaire of cell phone usability. Furthermore, muscle pressure and mental work load during cell phone use were evaluated by Borg CR10 and NASA-TLX questionnaires, respectively. Data were analyzed conducting statistical analysis tests of T-test and Mann-Whitney by SPSS24 software.
Results: Results revealed that the average typing speed and typing errors in touch-screen cell phones are larger than that in button cell phones. Moreover, the average of perceived usability in touch-screen cell phones (5.8) is higher than that in button cell phones (4.3). Pearson correlation coefficient showed an inverse relationship (-0.3) between perceived usability and mental work load obtained in both types of the cell phones. Findings showed that the maximum perceived muscle pressure when working with a cell phone is felt in the neck area.
Conclusion: According to the obtained results, touch-screen cellphones are suggested for those elders who type more and button cell phones are recommended for those who use the cell phone menu more frequently, namely taking photo, calling, internet, and so forth.
Ali Arabian, Bahador Makkiabadi, Sadegh Masjoodi, Kamal Azam, Ehsan Ghafari, Ebrahim Torabi Nassaj, Seyed Abolfazl Zakerian,
Volume 7, Issue 2 (Iranian Journal of Ergonomics 2019)
Abstract
Background and Objectives: In recent years, due to the rapid growth of metropolitan cities and the shortage of urban public transport means, including urban bus transportation, many people are forced to travel in a standing position when using these vehicles. This situation may cause pain and discomfort and non-collision injuries for passengers. The purpose of this study was ergonomic assessment of the sit-standing seat in passengers standing on urban buses.
Methods: To do this study, 8 young people with a mean age of 25.25±2.12 years were enrolled. For evaluation and assessing the effect of sit-standing seat two methods of surface Electromyography (sEMG) and Borg scale scores were applied in Fall 2018. The data was analyzed using SPSS 24.
Results: In all body parts, except for the hip, the mean scoring of Borg’s scale for perceived discomfort in sit-standing position was less than standing position. Also, the amount of contractile activity of the leg muscles in sit-standing position was significantly lower than the standing position (P<0.05).
Conclusion: Considering the results obtained from the Borg scale scores and the contraction activity of the leg muscles as a result of the use of the mentioned seat, which led to a reduction in the level of discomfort and the leg muscles contraction, it is recommended to apply the sit-stand seat instead of being in a standing position.
Majid Lashgari, Mohammadreza Arab, Mohsen Nadjafi, Ali Maleki,
Volume 9, Issue 2 (Iranian Journal of Ergonomics 2021)
Abstract
Background & Objectives: Due to the sound caused by various machines and tools in different agriculture sectors, occupational safety and health should be continuously evaluated. Indeed, the harmful effects of sound can be better reduced when the effects of sound on people's health and performance are fully known.
Methods: In this study, a garden tractor was used. Sixteen volunteers were exposed to the sound of the tractor, and their EEG was recorded at four different engine speeds. Then, Higuchi and Katz methods were used to calculate the fractal dimension of sound signals as well as brain signals.
Results: The results showed that by increasing engine speed, the values of the fractal dimension in both Higuchi and Katz methods increased. The results also showed an increase in the fractal dimension of brain signals due to an increase in engine speed. The regression results also showed a high correlation between the two brain signals and the sound. The coefficient of explanation was 0.896 and 0.859 in Higuchi and Katz methods, respectively.
Conclusion: This study showed that people's reactions, when exposed to sound, can be predicted using the fractal dimension. Therefore, it is possible to estimate the characteristics of brain signals without recording them, which are often costly and time-consuming.
Azam Maleki-Ghahfarokhi, Iman Dianat, Mohammad Asghari Jafarabadi, Mohamad Parnianpour, Mahmood-Reza Azghani, Maryam Khosravifar, Sina Samadi,
Volume 10, Issue 1 (Iranian Journal of Ergonomics 2022)
Abstract
Objectives: The comfort questionnaire for hand tools (CQH) is a subjective measure for exploring the starting points for improving hand tool design. This study aimed to investigate the psychometric properties of the Farsi version of the CQH.
Methods: In this cross-sectional study, which was conducted among 163 university students, the 17-question CQH was translated into Farsi with a translation back-translation procedure. Content validity was assessed by a panel of 10 experts. Exploratory Factor Analysis (EFA) was applied for determining construct validity. Cronbach’s alpha and Intraclass Correlation Coefficient (ICC) were used for assessing internal consistency and test-retest reliability, respectively. Ceiling and floor effects were also estimated for evaluating the feasibility of the measure.
Results: The CQH showed good content validity. Content validity index (CVI) ranged from 0.80 to 1.00 and Content Validity Ratio (CVR) ranged 0.62-1.00. EFA led to extraction of two factors from the data. The first one was mostly related to functionality and physical interaction and the second one, was generally about adverse body effects. The Cronbach’s alpha was 0.74 and test-retest reliability was 0.74 (95% CI = 0.58 to 0.86) which both were satisfactory. There were no (0%) ceiling and floor effects.
Conclusion: The Farsi version of CQH is an acceptable and useful instrument for evaluating hand tools comfort.
Davood Afshari, Maryam Nourollahi-Darabad, Noorollah Karimi, Maryam Seyed Tabib,
Volume 10, Issue 1 (Iranian Journal of Ergonomics 2022)
Abstract
Objectives: Nurses are at the front line of treatment and coping with COVID-19 pandemic. Therefore, the present study investigates the pandemic’s impact on nurses ’mental workload and determines its predictive factors.
Methods: This descriptive-analytical study was done on 234 nurses in two groups working at COVID-19 and non-COVID-19 wards in 2020. The criteria for entering the study were the absence of psychological problems. Data was gathered using the General Health Questionnaire, NASA-TLX, and Demographic Questionnaire.
Results: The mean of the overall mental workload score in the group of nurses working at the Covid-19 wards (70.09 ± 2.51) was higher than the group of nurses working in the non-COVID-19 wards (66.55 ± 2.02). This difference was significant (P = 0.01). There was a significant difference between the mean score of the mental demand, the physical demand, the temporal demand, and the frustration level of the two groups. With the exception of performance, the group of nurses working in the corona ward had a higher mean score in all aspects. In the proposed linear model, 16% of the overall changes in mental workload depended on two variables, which were age and work experience. The work experience was the most influential factor in predicting nurses' mental workload.
Conclusion: The findings of the present study showed the importance of paying attention to the mental workload of nurses as well as personal and occupational factors affecting mental workload in the conditions of the COVID-19 pandemic. Therefore, control and management of effective factors can help reduce mental workload, especially during pandemic conditions.
Hamed Yarmohammadi, Mehdi Jahangiri, Elham Arab Mokhtari,
Volume 11, Issue 3 (Iranian Journal of Ergonomics 2023)
Abstract
Objectives: A significant indicators of progress and development is the publication of books within any scientific domain. Ergonomics, a critical field associated with human and occupational health, contributes to enhancing productivity and the health level of employees. The present study aims to investigate the state of production and publication of ergonomics books in Iran.
Methods: The current study employed a descriptive approach and content analysis with a bibliometric perspective. The research population encompaased all ergonomics books registered on the National Library website. To access relevant books, searches were conducted without temporal limitations using keywords such as ergonomics, human factors engineering, and other related terms. The collected data were then entered into a pre-designed form in Excel software and, in the final stage, were analyzed using descriptive statistics.
Results: In total, 313 book titles in the field of ergonomics have been published between the years 1989 to 2023, indicating an increasing trend in the publication of books in this area. The highest frequency was for authored books, accounting for 78.27 percent of the publications. Mohammad Amin Mououdi, Majid Motamedzadeh, and Alireza Choobineh were the most active authors in this field. The subject areas of ergonomics principles and application, occupational ergonomics, and human factors engineering had the highest frequency. Fanavaran publications held the highest rank among all publishers. In total, 38 book titles reached multiple editions.
Conclusion: The results of the current study signify an upward trend in book publication within the field of ergonomics in Iran. However, there is a need for more attention from authors in some specializations of this science, including occupational biomechanics, urban ergonomics, ergonomics in domestic settings, and ergonomics for children. Additionally, there is a notable lack of focus on the publication of electronic books in this scientific field. Therefore, to give more consideration to the advantages of electronic books and consider their publication.
